The OnGuard Collision Mitigation System detects objects ahead and measures the vehicle's position in relation to others on the road to warn the driver of a possible rear-end collision by delivering audible, visual and haptic warnings. Check the screen for sensor output: If Sensor Output is displayed, the sensor test is complete. Toolbox allows technicians to view system faults, follow repair instructions, track wiring schematics, verify system integrity and efficiently adjust component operation. A copy of this bulletin is posted on our website, www. Component activation status appears in the status box field. Support the vehicle with safety stands.
The Sensor Orientation Test screen will appear. A copy of this bulletin is posted on our website, www. Language Restart Refer to page 5 of this manual for information about using the Language selection. Use the Save or Print button to save or print the fault information data. Support the vehicle with safety stands. OnGuard is always monitoring the road and provides warnings and active braking when deemed necessary, even when cruise control is not set. This will cause the stopping distance to increase and can result in serious personal injury.
These drivers must be procured from the manufacturer and installed separately. That is why OnGuard offers three levels of warnings to alert you to potential rear-end collisions. A pull down menu will appear. The new release — Toolbox 11. You must always disconnect the battery ground cable before working on the electrical system.
Clear each fault as it is repaired. The default value is 502. The following is a sample report. Notebook Select Notebook to enter or view information about a specific vehicle. A pull down menu will appear. A pull down menu will appear. Relay Select Relay from the pull down menu to turn the Retarder Relay on or off.
Use the update button to refresh the fault information table and display the new list of faults. Select Sensor Test to display the Sensor Test screen. The Valve Activation screen lets you activate the four valves, the pump and the retarder relay. A pull down menu will appear. Make sure sensed wheel ends are off of the ground.
Use the Save or Print button to save or print the fault information data. You must save all data according to the instructions given in Save, above. Do not let fluid get on brake pads, shoes, rotors or disks. Language Refer to page 5 of this manual for information about using the Language selection. Meritor Wabco launched its Toolbox 11 software package in May 2013. Bookmark and Thumbnail tabs at the side of the troubleshooting information sheet provide additional information. Use the Save or Print button to save or print the fault information data.
The lineup includes seven-way cable assemblies, tractor-trailer jumper air lines, tender kits and an expansion of brake hose assemblies that include dual live swivel fitting configurations. These include braking systems and controls, active safety systems, and suspension and control systems for commercial vehicles in North America. This rate equals a wheel speed of approximately 4 mph 7 kph. Restart Exit Help From the Main Screen you can select Restart, Exit or Help. Check the tooth wheel for damaged or missing teeth that could cause pulses to be missing on each rotation of the wheel.
From the Main Screen, you can select Restart, Exit or Help. Please refer to page 25 for more information about Save and Print functions. Select Raise to raise the vehicle chassis to the ride height or Lower to lower the vehicle chassis to the ride height low level. Current settings will be shown. Meritor Wabco v12 Software — Now Available! As each lamp is tested, check the actual lamp to verify correct operation. Fault Information Sheet This is an example of a Fault Information Sheet. Click on the Activate button and listen for the valve to click, indicating a good installation.
Failure to keep the brake reservoir level above minimum could result in more air entering system, making it impossible to effectively bleed the system. Serious personal injury and damage to components can result. These sheets are available in version 5. Do not work under a vehicle supported only by jacks. This is helpful in verifying correct operation, installation and wiring of the unit under test. The Report Information Screen will appear.
Jacks can slip and fall over. This is also helpful in verifying correct operation, installation and wiring. Revised 01-04 For detailed repair instructions, click on the fault to display a troubleshooting information sheet. A pull down menu will appear. Faults Select faults from the pull down menu. A pull down menu will appear.